youritronics.com
Youritronics: DIY, Electronics, IT and Gadgets - Part 2
http://www.youritronics.com/page/2
DIY, Electronics, IT, Gadgets. April 1st, 2015. VoltLog #10 – HP 3478A Line Voltage and Frequency Adjustment 110V 60Hz to 230V 50Hz. March 23rd, 2015. VoltLog #9 – InTheMail HP 3478A, Probe Master 8028S, Anker Astro E3, Seagate Expansion 2TB. In this InTheMail segment I receive the HP 3478A 5.5 digit multimeter, a Probe Master 8028s test lead set, the Anker Astro E3 10000mAh portable battery charger and the Seagate Expansion 2TB external storage hard drive. March 16th, 2015. March 6th, 2015. In this vide...
starlino.com
Using USBThumb as a Propeller Programmer and as a USB to Serial Converter « Starlino Electronics
http://www.starlino.com/usbthumb_propeller_programmer.html
Acc Gyro 6DOF Analog IMU: 3 Axis Accelerometer 3 Axis Gyro. Single Axis Analog Gyroscope with Noise and Drift Filters. Usb Thumb Sized Pic Development Platform (PIC18F14K50). Using USBThumb as a Propeller Programmer and as a USB to Serial Converter. Posted on: March 15, 2010 by. The Parallaxs classic propeller programmer PropPlug is simply a USB to Serial converter, the DTR/RTS signals are used to reset the Propeller chip before starting the programming sequence. USBThumb (loaded with USBThumbSerial.
starlino.com
Updating Firmware on USBThumb « Starlino Electronics
http://www.starlino.com/usbthumb_firmware_upgrade.html
Acc Gyro 6DOF Analog IMU: 3 Axis Accelerometer 3 Axis Gyro. Single Axis Analog Gyroscope with Noise and Drift Filters. Usb Thumb Sized Pic Development Platform (PIC18F14K50). Updating Firmware on USBThumb. Posted on: March 18, 2010 by. Can be programmed with different firmware, including all Microchip samples from USB Framwework. Use the ones for low pin count USB demo board). This can achieved by placing a jumper wire or a 1K resistor (recommended) between GND and VPP pin. Next insert the USBThumb into ...
starlino.com
Removing stubborn 3D prints from bed (my way of doing it) « Starlino Electronics
http://www.starlino.com/removing-stubborn-3d-prints-from-bed-my-way-of-doing-it.html
Acc Gyro 6DOF Analog IMU: 3 Axis Accelerometer 3 Axis Gyro. Single Axis Analog Gyroscope with Noise and Drift Filters. Usb Thumb Sized Pic Development Platform (PIC18F14K50). Removing stubborn 3D prints from bed (my way of doing it). Posted on: June 14, 2015 by. Here is my method of removing stubborn prints from your 3D printer’s bed. This method does minimum damage to the bed coating (painter’s tape / capton tape). All you need is box cutter. Follow 3 easy steps:. Type the text displayed above:. Combine...
starlino.com
Introducing the QuadHybrid – a stable, maneuverable and cheap flying robotic platform « Starlino Electronics
http://www.starlino.com/quadhybrid_intro.html
Acc Gyro 6DOF Analog IMU: 3 Axis Accelerometer 3 Axis Gyro. Single Axis Analog Gyroscope with Noise and Drift Filters. Usb Thumb Sized Pic Development Platform (PIC18F14K50). Introducing the QuadHybrid – a stable, maneuverable and cheap flying robotic platform. Posted on: December 2, 2012 by. IMU Theory and Experiments. Introduction and Demo of the Quad. Without further adieu below is the picture of the machine that I called QuadHybrid :. My very first QuadHybrid prototype. So What Exactly is a Quad.
starlino.com
Quicktip: Program your RC transmitter with UsbThumb « Starlino Electronics
http://www.starlino.com/quicktip-program-your-rc-transmitter-with-usbthumb.html
Acc Gyro 6DOF Analog IMU: 3 Axis Accelerometer 3 Axis Gyro. Single Axis Analog Gyroscope with Noise and Drift Filters. Usb Thumb Sized Pic Development Platform (PIC18F14K50). Quicktip: Program your RC transmitter with UsbThumb. Posted on: January 13, 2014 by. If you own a low-end RC transmitter with the Trainer port, you can program it using USBThumb. Using the default USBThumbSerial. Firmware https:/ code.google.com/p/usbthumb/. Type the text displayed above:. Get Updates of this post/comments by email.
starlino.com
Build a 8A (4A per motor) dual motor driver for under $10. Introducing OctoDriver – poor man’s motor controller. « Starlino Electronics
http://www.starlino.com/motor_driver.html
Acc Gyro 6DOF Analog IMU: 3 Axis Accelerometer 3 Axis Gyro. Single Axis Analog Gyroscope with Noise and Drift Filters. Usb Thumb Sized Pic Development Platform (PIC18F14K50). Build a 8A (4A per motor) dual motor driver for under $10. Introducing OctoDriver – poor man’s motor controller. Posted on: August 26, 2009 by. Now what do you do if you need more power? Without much talk below is the schematic:. As far as enable inputs we combine 12EN & 34EN for each chip. This is where well send our PWM signal.
